Arts of Steel Limited fabricates high-privacy boarded steel gates in Surrey and SW London, featuring Circular Recycled Nylon-Polymer, Reinforced Wood-Fibre, and Contrast Aluminium-Backed options.








Built from a heavy-duty 60mm steel profile frame to house both the outer nesting subframe and rear pressurising subframe, these bespoke composite gates eliminate board rattling while incorporating engineered water drainage to prevent winter frost damage. The flanking railings integrate a front-slot, rear-retrievable secure postbox visible in the diagonal elevation (55A3).
Equipped with a 4G GSM mobile intercom system allowing the homeowner to speak with visitors and command the gates open or closed from anywhere via their mobile phone and dedicated smartphone app.






Combining an architectural dark grey 60mm steel frame with light-toned composite timber cladding secured between custom outer and inner subframes, these contemporary gates are specially hinged from the top of the frame—eliminating side hinge gaps to achieve maximum privacy blockage, anti-intruder security, and finger-trap safety during operation.
Driven by concealed underground hydraulic operators and controlled via a 4G GSM mobile technology intercom with dedicated smartphone app access.








Constructed with a 60mm structural frame, inner nesting subframe, and rear pressurising subframe housing ultra-robust composite boards exceeding 30mm in thickness (photo 55C8), these gates were trial-assembled in our Surrey workshop prior to coating (photos 55C4–55C7). Special offset hinges allow up to 180-degree opening so the entire driveway aperture between posts clears completely (photo 55C3).
Equipped with a 4G GSM mobile intercom with smartphone app control, complemented by front-elevation post downlights and flush-fitted face-to-face inner post lights that illuminate the gate after dark (photo 55C1).










Finished in jet black wrought iron framing with light grey composite boards, this double pedestrian gate and flanking fence system is engineered with an outer nesting subframe and a rear pressurising subframe clamped so there are zero visible screws through the gate faces. For daily convenience, the primary leaf opens via code and handle (assisted by a gas spring auto-closer), while releasing its internal drop bolt allows the second leaf to swing open wide whenever bulky items need to pass through.
Equipped with a back-to-back keypad housed inside a bespoke welded subframe (tested in our workshop prior to coating in photos 55D9 and 55D10), providing effortless keyless entry and exit from either side.





Constructed from the same black wrought iron and light grey composite materials as Case Study 4, this single-leaf pedestrian security gate features a heavy-duty outer frame tailored to fit neatly within an existing brick archway. Anchored with high-strength chemical resin fixings and internally accessible bolts, the exterior elevation presents a clean, fastener-free appearance.
Built with reinforced inner and rear subframes, heavy-duty hinges, a hydraulic/gas auto-closer, and a workshop-tested keyless keypad (photos 55E4 and 55E5).





Installed at the rear entrance of St George’s Junior School, Weybridge—where Arts of Steel Limited has fabricated and installed the majority of the gates at St George’s Junior and 90% of the architectural metalwork across St George’s Senior (featured in our Schools & Colleges division)—this 50mm profile wrought iron gate incorporates the school emblem within the vertical bars and double horizontal tie bars for maximum structural rigidity.
Backed at the rear with a precision-trimmed, tapped, and bolted 3mm thick aluminium sheet powder-coated in St George’s signature cherry red colour to provide full visual privacy and bold architectural contrast (rear views 55F4 and 55F5).




Engineered for uncompromising privacy and perimeter security, this heavy-duty wrought iron electric sliding gate is fitted with rear-bolted aluminium backing panels that block sightlines completely while retaining classic ironwork aesthetics on the street elevation.
Accompanied by bespoke matching boundary railings with recessed bar detailing (photo 55G4) fabricated in-house to create a unified, high-security frontage.






Featuring a jet black steel outer frame paired with a dark grey bolted aluminium backing sheet for subtle two-tone architectural depth, these pedestrian security gates are equipped with heavy-duty mechanical keypads for reliable keyless access and special hinge geometry allowing the gate leaf to fold back completely flush against the boundary wall (photo 55H2).
Also shown in this collection is a full-width double-leaf electric boarded driveway gate built with the same contrast aluminium backing technique (photo 55H6).
Produced in our in-house CAD drafting department, these four technical drawings specify the exact engineering method used across our composite-infill gates—detailing the primary outer subframe that nests the composite timber boards inside the 60mm main frame and the secondary rear subframe that clamps and pressurises the boards firmly in place.
The sectional drawings illustrate how both subframes lock together without any visible through-screws on the gate face while incorporating dedicated bottom water-drainage channels so rainwater escapes freely without freezing or expanding inside the frame during winter.
Every metal-framed composite gate from Arts of Steel Limited combines a heavy-gauge hot-dip galvanised and powder-coated structural steel chassis with low-maintenance woodgrain composite or custom RAL-coloured aluminium infill boards—engineered for swing, tracked sliding, and cantilever entrances across West Byfleet, Weybridge, Ripley, Woking, Guildford, and SW London.
Send us photographs of your driveway entrance and preferred design style so our engineers can provide free initial technical advice and a ballpark estimate—review our Quotation Request Process, explore our Metal-Framed Composite Gates Gallery, or contact our team here.